Commercial & Industrial Systems

Home / Commercial & Industrial Systems

Features:

This system adopts high efficient TFR RO membrane to ensure safe drinkable water.

8-stage filtration, combines advantage of each filter to remove dirt, colloid, suspended substances, organisms, heavy metals, dissolved solid, bacteria, virus, etc. and keep only pure water with oxygen through.

Equipped with silent pump, providing stable water pressure to produce pure water.

Microprocessor Controlled:

  • Digital display purification processing
  • Auto-flush RO membrane periodically
  • Purification processing and water tank full indication
  • Digital display TDS of the production water (in PPM)
  • Automatic off when water supply is cut off and when tank is full
  • Factory tested and sterilized
  • Comprehensive limited warranty
  • Packaged, ready for shipment

Untitled-1

Specifications:

Voltage: 220V / 50Hz, 110V / 60Hz

Available with 100 GPD / 150 GPD / 200 GPD / 300 GPD production rate

Tank: 10 Gallon

Pressure Requirement: 0.1 – 0.3 MPa

Temperature:4°C to 38°C (40°F to 100°F)

500-1500-GPD
Standard Features :

  • Stainless steel frame stand. Designed for municipal/tap water source.
  • High rejection thin film RO membranes
  • Stainless steel frames,
  • Efficient, high pressure pumps & motors
  • Electronic controls
  • Continuous TDS monitoring built-in
  • Flow meters for product water & concentrate
  • Pressure regulator valves for inlet and concentrate
  • 316L stainless steel membrane housings (300G-600G-800G) .
  • GRP membrane housings (1500~14000G) .
  • Heavy-duty pressure tubing (as on larger models)
  • PROCON high pressure pump (300~1500G).

1500-3000-GPD

Standard Features :

  • Stainless steel frame stand. Designed for municipal/tap water source.
  • 200psi of operation pressure.
  • Reliable quality components utilized for system construction.
  • Optimum water recovery.
  • Electro-mechanical relay logic control circuit.
  • Dual-level tank switches and controls.
  • Plumbed for optimum water recovery.

FEED WATER PARAMETERS:

3000-6000-GPD

Standard Features :

  • Max. Temperature 85 F.
  • Max. pressure between 40-80 psi.
  • Max. TDS 2,000 ppm.
  • Max. iron tolerance 0.5 ppm.
  • Hydrogen sulfide must be removed.
  • Silica tolerance can not be higher than 125 ppm in the concentrate stream. Antiscalant shouldbe considered
    for any levels over 75 ppm.
  • Turbidity should be removed.
  • Harness must be removed.
  • Low pressure shut-off and restart
  • Pre-filter housings and cartridges (300 to 5,400 GPD models)
  • Starter motor box
  • On / off switch
  • Solenoid valves for pump and flush cycle
  • Gate valves

OPERATING PARAMETERS:

3000-6000-GPD2

Standard Features :

  • Max. Operating pressure 200 psi.
  • Water recovery up to 60% but not recommended to adjust higher than 50%.
  • pH range 3-11.
  • Flow rates are determined by the membrane mfg's testing criteria of 1500 ppm NaCI solution, 77 F
    water temperature, 225 psi at 10-15% recovery. Actual flow rates may vary depending on the pretreatment,
    water conditions, system volume, membrane array and operation pressure.
  • Grondfos high pressure pump (1500~14000G).
  • Low pressure shut-off and restart
  • Pre-filter housings and cartridges (300 to 5,400 GPD models)*
  • Starter motor box
  • On / off switch
  • Solenoid valves for pump and flush cycle
  • Gate valves
  • Anti-scalent device
  • Factory tested and sterilized
  • Comprehensive limited warranty
  • Packaged, ready for shipment